0x00009881
0x01110fff


RSLR0=00000249 RDGR0=00000055
Stage 00 Result 00000000
Stage 01 Result 00000000
Stage 02 Result 00000000Systemp Started
0x12345678
Boot From SPI0x12345678
ucl decompress
decompress finished
ready


U-Boot 2010.06froyo-amlogic-mid-20110526-431-gb02a890(dvbc_8726m1_v1) (Oct 28 2011 - 16:20:01)

DRAM:  512 MiB
unknow ddr type
NAND:  Amlogic nand flash uboot driver for m1, Version 1.1 (c) 2010 Amlogic Inc.
NAND device id: ec d5 84 72 50 42
NAND device: Manufacturer ID: 0xec, Chip ID: 0xec (Samsung 6 Generation NAND 2GiB K9GAG08U0E)
1 NAND chips detected
oob size is not enough for selected bch mode: ’ force bch to mode: NAND_BCH16_MODE
multi plane error for selected plane mode: NAND_TWO_PLANE_MODE force plane to : NAND_SINGLE_PLANE_MODE
aml nand env valid addr: 0
 NAND bbt detect Bad block at a00000
Creating 2 MTD partitions on "nandnormal":
0x000000800000-0x000001100000 : "mtd1"
 NAND bbt detect Bad block at a00000
0x000001100000-0x000011100000 : "mtd2"
nandnormal initialized ok
MMC:   SDIO Port A: 0
SF: Got idcode ef 40 15
SF: Detected W25Q16 with page size 4096, total 2097152 bytes

SPI NOR Flash have write protect!!!
In:    serial
Out:   serial
Err:   serial
KGDB:  ready
Net:   select eth clk-1,source=400000000,out=50000000
Apollo EMAC
Dcache status 1
Icache status 1
Set HDMI:Chip C
ENTER U-BOOT SWITCH MODE !!!!
get_adc_sample(4): 0x0
get_adc_sample(4): 0x0
get_adc_sample(4): 0x0
get_key(): 1
get_adc_sample(4): 0x0
get_key(): 1
get_adc_sample(4): 0x0
get_key(): 1
get_adc_sample(4): 0x0
get_key(): 1
get_adc_sample(4): 0x0
get_key(): 1

NAND read: offset 0x800000, size 0x800000
 NAND bbt detect Bad block at a00000
 NAND bbt detect Bad block at a00000
Skipping bad block 0x00a00000
 8388608 bytes read: OK
i =4
outputmode = 720p
Begin scale logo...
There is no valid bmp file at the given address
osd : 24 (1280,720) osd1
chip version=e5832fe0, serial:0xB
used Video pll for video out!!
dac index:1 ,signal:PROGRESSIVE_Y
dac index:2 ,signal:PROGRESSIVE_PB
dac index:0 ,signal:PROGRESSIVE_PR
set mode VIC -1887970912 (cd4,cs0,pm1196380752,vd-1887970912,8f83a0a0)
There is no valid bmp file at the given address
not set screen size yet
Recovery Start...
Recovery Start...

Partition Map for UNKNOWN device 0  --   Partition Type: DOS

Partition     Start Sector     Num Sectors     Type
    1                16065          224910       b
Device: SDIO Port A
Manufacturer ID: 0
OEM: 0
Name: Tran Speed: 20000000
Rd Block Len: 512
SD version 1.0
High Capacity: No
Capacity: 128450560
Bus Width: 4-bit

Partition Map for UNKNOWN device 0  --   Partition Type: DOS

Partition     Start Sector     Num Sectors     Type
    1                16065          224910       b
        uImage_recovery is exist
recovery in SD Card!!!
reading uImage_recovery

3771652 bytes read
## Booting kernel from Legacy Image at 82000000 ...
   Image Name:   Linux-2.6.34
   Image Type:   ARM Linux Kernel Image (lzma compressed)
   Data Size:    3771588 Bytes = 3.6 MiB
   Load Address: 80008000
   Entry Point:  80008000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
Using machid 0xb8d from environment

Starting kernel ...